The Power of Being There®
Quick Installation Guide
®
®
Cybex SwitchView
SC8 DVI Switch
The following instructions will help you
install your SwitchView SC8 DVI switch.
Should you require further assistance, please
contact Avocent Technical Support.
To install the Cybex SwitchView SC8 DVI switch
4
2
Connecting local peripherals
1
Power down all servers that will be part of your
SwitchView SC8 DVI switching system. Locate
your PS/2 keyboard, DVI monitors and PS/2
mouse. Plug your DVI monitor cables into the
CONSOLE ports on the left side of the back
of your switch. Plug your PS/2 keyboard cable
and your PS/2 mouse cable into the keyboard
and mouse ports respectively.
CONSOLE
H
G
F
E
D
C
B
A
Optional
RF ground
(not required
for safety)
1
Connecting your servers
2
Locate your first cable set consisting of two
PS/2 cables and one or two DVI cables. The
SwitchView SC8 DVI switching system has
eight port sets labeled A-H on the rear of the
unit. Plug the two PS/2 cables (keyboard
and mouse) and the DVI cable (monitors)
into the corresponding ports on your server.
Plug the other ends into any available server port
setonyourSwitchViewSC8DVIswitchingsystem.
Repeat this process until all servers are properly
attached to the SwitchView SC8 DVI switch.
3
Input Power: 60 W; Operating Voltage 100-240 VAC
Power Frequency: 50-60 Hz
Switching your servers
4
Press the appropriate front panel button labeled A-H to
Supported Hardware
access servers in your SwitchView switching system.
Server: IBM, PC/AT, PS/2 and 100% compatibles
Video Modes: VGA, SVGA, XGA, SXGA, UXGA,
HDTV and QXGA
LEDs
Turning on your system
3
Each target port (A-H)has dual LEDs on the front panel. A
greenLEDindicatesthetargetdeviceisonandconnected
to the switch. An amber LED indicates the target device
is selected (KVM session).
Loc ate the power cord that c ame with your switch.
Plug one end into the IEC power connector on
theSwitchViewswitch.Ensurethepowerswitch
is off, then plug the other end of the power cord
into an AC wall outlet. Turn on your switch first,
then turn on all attached servers.
Maximum Resolution: 2048 x 1536 @ 75Hz
Peripherals: PS/2 keyboard, PS/2 mouse and
IntelliMouse (PS/2 only)
Environmental
Mechanical
Operating Temperature: 41˚ (5˚C) to 104˚ (40˚C)
Storage Temperature: -4˚ (-20˚C) to 122˚ (50˚C)
H x W x D = 3.6” x 17.2” x 10.8” (9.1 x 43.7 x 27.4 cm)
Weight = 9.5 lbs (4.3 kg)
Avocent, the Avocent logo, The Power of Being There, Cybex and SwitchView are registered trademarks of Avocent Corporation or its affiliates. ©2007 Avocent Corporation. All rights reserved.
590-502-501D
|
Advanced Global Technology Digital Camera QSP 660 User Manual
Agilent Technologies Network Router E4400 60230 User Manual
Alamo Lawn Mower 00785503C User Manual
Altec Lansing Portable Speaker 403A User Manual
Alvin High Chair CE101 User Manual
AMC Home Theater System XN 11n User Manual
Ask Proxima Projector AV 9350 User Manual
Ativa Calculator PET1030 User Manual
Bakers Pride Oven Oven BK 18 User Manual
Beko Air Conditioner LG BKE4500 D LG BKE5505 D User Manual