Avocent Switch SC4UAD 001 User Manual

The Power of Being There®  
Quick Installation Guide  
®
SwitchView SC4 UAD  
DVI/USB Switch with Audio  
The following will help you install your  
SwitchView SC4 UAD switch easily.  
Should you require further assistance, please  
contact Avocent Technical Support.  
To install the SwitchView SC4 UAD switch  
Connecting local peripherals  
1
4
Turn off all servers that will be part of your  
SwitchView SC4 UAD switching system. Locate  
your USB keyboard, DVI monitor, USB mouse,  
speakersandmicrophone.Plug yourDVI monitor  
cable into the appropriate CONSOLE port on  
the left side of the back of yourswitch. Plug your  
USB keyboard cable and yourUSB mouse cable  
into the keyboard and mouse ports respectively.  
Plug your speaker cable and microphone cable  
into the corresponding ports.  
Optional  
RF ground  
(not required for  
safety)  
2
3
1
2
Connecting your servers  
Locate your first cable set consisting of one USB  
cable, one DVI cable and two audio cables. The  
SwitchView SC4 UAD switching system has four  
port sets labeled A-D on the rear of the unit. Plug  
the USB cable, the two audio cables (speaker  
and microphone) and the DVI cable (monitor)  
into the corresponding ports on your server.  
Plug the otherends into any of the available server  
port sets on your SwitchView SC4 UAD switch.  
Repeat this process until all servers are properly  
attached to the SwitchView SC4 UAD switch.  
switch. Plug one end into the IEC power connector on  
the SwitchView SC4 UAD switch. Ensure the power  
switch is off, then plug the other end of the power  
cord into an AC wall outlet. Turn on your switch first,  
then turn on all attached servers.  
Environmental  
Operating Temperature: 41˚ (5˚C) to 104˚ (40˚C)  
Storage Temperature: -4˚ (-20˚C) to 122˚ (50˚C)  
Input Power: 60 W; Operating Voltage 100-240 VAC  
Power Frequency: 50-60 Hz  
Supported Hardware  
Switching your servers  
4
Server: IBM, Sun, PC/AT, USB and 100% compatibles  
Video Modes: VGA, SVGA, XGA, SXGA, UXGA,  
WVGA, WSVGA, WXGA, WSXGA, WUXGA,  
and HDTV  
Press the appropriate front panel button labeled A-D to  
access servers in your SwitchView switching system.  
LEDs  
Eachtargetport(A-D)hasasinglebi-colorLEDonthefront  
panel.The LED will be green when the target device is on  
andconnectedtotheswitch.TheLEDwillchangetoamber  
when the target device is selected (KVM session).  
Mechanical  
Maximum resolution: Single link DVI up to  
1920 x 1200 @ 60Hz (monitor and video card support  
for the maximum resolution will vary and should be  
verified for compatibility)  
NOTE: Cable sets without audio cables are  
available if you do not require speaker and  
microphone support.  
Peripherals: USB keyboard, USB mouse and  
IntelliMouse (USB only)  
3
Powering your system  
H x W x D = 1.75” x 11” x 11” (4.44 x 27.94 x 27.94 cm)  
Weight = 4.9 lbs (2.2 kg)  
Locate the power cord that came with your  
To Contact Avocent Technical Support: Visit www.avocent.com  
Avocent, the Avocent logo, The Power of Being There, the Cybex logo and SwitchView are registered trademarks of Avocent Corporation or its affiliates. ©2007 Avocent Corporation. All rights reserved.  
 
590-609-501B  

321 Studios Two Way Radio OL 7141 04 User Manual
Aastra Telecom Telephone 1600IP User Manual
Adcom TV Receiver GTP 740 User Manual
Addonics Technologies Computer Drive SCCHDISA128 User Manual
ADS Technologies Switch USBH 2004 User Manual
Agilent Technologies VCR 8922 User Manual
Alamo Lawn Mower JD 5225 User Manual
Altec Lansing Stereo Amplifier 1707C User Manual
Aluratek Computer Drive AHDU350 User Manual
American Audio Stereo Amplifier VLP Series User Manual